Changes between Version 3 and Version 4 of netmon2017snmp

Timestamp:

Nov 6, 2017, 10:36:57 AM (7 years ago)

Author:

admin

Comment:

--

netmon2017snmp

@@ -9 +9 @@
  - Download and install virtualbox 5.0.x​
  - Download the Virtual Hard disks from the LEARN mirror. You can get them by following links
-    * [http://192.248.4.49/ipv6/NetMon.vdi CampusLAN.vdi]
+    * [http://192.248.4.49/ipv6/Netmon.vdi Netmon.vdi]
  - Note down the location of downloaded vdi files
 
-=== Creating the VM !NetMon ===
+=== Creating the VM Netmon ===
 
  - Start !VirtualBox and Click on '''New''' button (at top-right) to create new virtual machine
- - Enter name of the VM as '''!NetMon''' 
+ - Enter name of the VM as '''Netmon''' 
  - Select OS Type: '''Linux'''
  - Select Version: '''Ubuntu (64-bit)'''
  - Then click on Continue button
  - Set VM's memory size to '''2048MB''' and click on Continue button
- - Set VM's hard disk option to '''Use an existing virtual hard disk file''' and click the browse button and browse to the location where you download the virtual hard disks. Then select the '''NetMon.vdi''' file and click on the create button.
- - You will see a new virtual machine named CampusLAN appears on Virtual Box Manager Window
+ - Set VM's hard disk option to '''Use an existing virtual hard disk file''' and click the browse button and browse to the location where you download the virtual hard disks. Then select the '''Netmon.vdi''' file and click on the create button.
+ - You will see a new virtual machine named Netmon appears on Virtual Box Manager Window
 
 ==== Setting up Network Interfaces ====
 
- - Select the !NetMon VM from left panel on Virtual box, right click and open '''Settings'''
+ - Select the Netmon VM from left panel on Virtual box, right click and open '''Settings'''
  - Click on the '''Network''' title
  - On '''Adapter 1''' check the '''Enable Network Adapter''' . Then change '''Attached to be''' to the '''Bridged Adapter''' and make sure the '''name''' of the interface is the same interface which you use to connect to the outside (Either Wi-Fi or Ethernet). This virtual interface will work as the WAN port of the of your virtual campus network that can be used to connect from out side. 
@@ -31 +31 @@
  - Click '''OK'''
 
-==== CampusLAN VM ====
+==== Netmon VM ====
 
 Before running Dynagen you have to start your VMs and assign IP address to the VM's network interfaces.
 
- - Select the '''CampusLAN''' VM from left panel on Virtual box, right click '''Start''' and wait till the VM starts
+ - Select the '''Netmon''' VM from left panel on Virtual box, right click '''Start''' and wait till the VM starts
  - login to the machine using the following user credentials
 {{{
@@ -81 +81 @@
           RX bytes:99387 (99.3 KB)  TX bytes:567441 (567.4 KB)
 
-enp0s8    Link encap:Ethernet  HWaddr 08:00:27:f0:f7:66
-          inet6 addr: fe80::a00:27ff:fef0:f766/64 Scope:Link
-          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
-          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
-          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
-          collisions:0 txqueuelen:1000
-          RX bytes:0 (0.0 B)  TX bytes:648 (648.0 B)
-
-enp0s9    Link encap:Ethernet  HWaddr 08:00:27:51:68:d3
-          inet6 addr: fe80::a00:27ff:fe51:68d3/64 Scope:Link
-          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
-          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
-          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
-          collisions:0 txqueuelen:1000
-          RX bytes:0 (0.0 B)  TX bytes:648 (648.0 B)
 
 lo        Link encap:Local Loopback