wiki:ipv6vmconf

Version 9 (modified by admin, 8 years ago) ( diff )

--

IPv6 in a Campus Network Hands - On

In this Hands-on yu will get a virtual campus LAN and through out the lab session you will configure the devices (Cisco based) in both IPv4 and IPv6. After all the configuratons you will get a virtual campus network with dual stack.

To simulate the Campus network you will use Dynagen/Dynamips.

For this hands-on we will give you a Virtual Hard Disk and Usng that you can create a virtual machine (Ubuntu 64 installed) with Dynagen/Dynamips installed. You will also find the network topology file in the VM as well.

Other than dynagen/dynamips installed VM you will get another two virtual hard disks which you can used as user PC's in two different VLANS in your virtual campus LAN.

Setting up the Virtualbox

Installation of virtualbox and Downloading virtual hard disks

  • Download and install virtualbox 5.0.x​
  • Download the Virtual Hard disks from the LEARN mirror. You can get them by following links
  • Note down the location of downloaded vdi files

Creating the VM campuslan

  • Start virtualbox and Click on New button (at top-right) to create new virtual machine
  • Enter name of the VM as campuslan
  • Select OS Type: Linux
  • Select Version: Ubuntu (64-bit)
  • Then click on Continue button
  • Set VM's memory size to 1536MB and click on Continue button
  • Set VM's hard disk option to Use an existing virtual hard disk file and click the browse button and browse to the location where you download the virtual hard disks. Then select the campuslan.vdi file and click on the create button.
  • You will see a new virtual machine named campuslan appears on Virtual Box Manager Window

Setting up Network Interfaces

  • Select the campuslan VM from left panel on Virtual box, right click and open Settings
  • Click on the Network title
  • On Adapter 1 check the Enable Network Adapter . Then change Attached to be to the Bridged Adapter and make sure the name of the interface is the same interface which you use to connect to the outside (Either Wi-Fi or Ethernet). This virtual interface will work as the WAN port of the of your virtual campus network (Can be connect from out side).
  • Click on Advanced drop down list and change the promiscuous mode to Allow All
  • On Adapter 2 check the Enable Network Adapter . Then change Attached to be to the Internal Network and give the Name of the network as VLAN10. This virtual interface will connect to a internal virtual bridged network.
  • Click on Advanced drop down list and change the promiscuous mode to Allow All
  • On Adapter 3 check the Enable Network Adapter . Then change Attached to be to the Internal Network and give the Name of the network as VLAN20. This virtual interface will connect to a internal virtual bridged network.
  • Click on Advanced drop down list and change the promiscuous mode to Allow All
  • Click OK

Creating the VM FacAPC

  • Start virtualbox and Click on New button (at top-right) to create new virtual machine
  • Enter name of the VM as FacAPC
  • Select OS Type: Linux
  • Select Version: Ubuntu (64-bit)
  • Then click on Continue button
  • Set VM's memory size to 512MB and click on Continue button
  • Set VM's hard disk option to Use an existing virtual hard disk file and click the browse button and browse to the location where you download the virtual hard disks. Then select the FacAPC.vdi file and click on the create button.
  • You will see a new virtual machine named FacAPC appears on Virtual Box Manager Window

Setting up Network Interface

  • Select the FacAPC VM from left panel on Virtual box, right click and open Settings
  • Click on the Network title
  • On Adapter 1 check the Enable Network Adapter . Then change Attached to be to the Internal Network and give the Name of the network as VLAN10. This virtual interface will connect to a internal virtual bridged network.
  • Click on Advaned drop down list and change the promiscuous mode to Allow All
  • Click OK

Creating the VM FacBPC

  • Start virtualbox and Click on New button (at top-right) to create new virtual machine
  • Enter name of the VM as FacBPC
  • Select OS Type: Linux
  • Select Version: Ubuntu (64-bit)
  • Then click on Continue button
  • Set VM's memory size to 512MB and click on Continue button
  • Set VM's hard disk option to Use an existing virtual hard disk file and click the browse button and browse to the location where you download the virtual hard disks. Then select the FacBPC.vdi file and click on the create button.
  • You will see a new virtual machine named FacBPC appears on Virtual Box Manager Window

Setting up Network Interface

  • Select the FacAPC VM from left panel on Virtual box, right click and open Settings
  • Click on the Network title
  • On Adapter 1 check the Enable Network Adapter . Then change Attached to be to the Internal Network and give the Name of the network as VLAN20. This virtual interface will connect to a internal virtual bridged network.
  • Click on Advaned drop down list and change the promiscuous mode to Allow All
  • Click OK

After Creating all three VM's. Your VM setup will look like this.

https://ws.learn.ac.lk/raw-attachment/wiki/ipv6vmconf/VMSetup.jpg

Setting UP IP Addresses

campuslan VM

Before running Dynagen you have to assign IP address to the VM's network interfaces.

  • Select the campuslan VM from left panel on Virtual box, right click Start and wait till the VM starts
  • login to the machine using the following user credentials 
    usrname  : learn
password : <classpassword>
  • Then change the interfaces file. Root password is the same as class password 
    sudo vi /etc/network/interfaces
  • locate the following lines 
    iface enp0s3 inet static
 address 192.168.56.2
 netmask 255.255.255.0
 network 192.168.56.0
 broadcast 192.168.56.255
 gateway 192.168.56.1
 dns-nameservers 192.248.1.161
  • Change it to the following lines. You can find your IP Address from this table 
    iface enp0s3 inet static
 address <Your IP Address >
 netmask 255.255.255.0
 network 192.248.4.0
 broadcast 192.248.4.255
 gateway 192.248.4.254
 dns-nameservers 192.248.1.161
  • Save and Exit the editor (type :wq)
  • When you completed the IP settings , restart the Interfaces 
    sudo /etc/init.d/networking restart
  • Confirm the correct IP settings by ipconfig command. Your result should be something like the following. Check the IP address of enp0s3 Interface and see whether the other interfaces are up 
    enp0s3    Link encap:Ethernet  HWaddr 08:00:27:8c:e0:26
          inet addr:<your IP address>  Bcast:192.248.4.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fe8c:e026/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1120 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7550 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:99387 (99.3 KB)  TX bytes:567441 (567.4 KB)

enp0s8    Link encap:Ethernet  HWaddr 08:00:27:f0:f7:66
          inet6 addr: fe80::a00:27ff:fef0:f766/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:648 (648.0 B)

enp0s9    Link encap:Ethernet  HWaddr 08:00:27:51:68:d3
          inet6 addr: fe80::a00:27ff:fe51:68d3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:648 (648.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:160 errors:0 dropped:0 overruns:0 frame:0
          TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1
          RX bytes:11840 (11.8 KB)  TX bytes:11840 (11.8 KB)
  • Try ping to some known hosts and see the results. 
    ping 192.248.4.254
ping 192.248.1.161
ping www.google.com

FacAPC VM

As this is a PC inside your virtual LAN it has a private IP address. The address is already configured. You can verify whether it is correct.

  • Select the FacAPC VM from left panel on Virtual box, right click Start and wait till the VM starts
  • login to the machine using the following user credentials 
    usrname  : learn
password : <classpassword>
  • Check the IP address by using the command ifconfig. The result should be as following. 
    enp0s3    Link encap:Ethernet  HWaddr 08:00:27:e9:76:20
          inet addr:10.0.10.1  Bcast:10.0.10.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fee9:7620/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:198 errors:0 dropped:0 overruns:0 frame:0
          TX packets:71 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:23291 (23.2 KB)  TX bytes:15516 (15.5 KB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:160 errors:0 dropped:0 overruns:0 frame:0
          TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1
          RX bytes:11840 (11.8 KB)  TX bytes:11840 (11.8 KB)

FacBPC VM

As this is a PC inside your virtual LAN it has a private IP address. The address is already configured. You can verify whether it is correct.

  • Select the FacBPC VM from left panel on Virtual box, right click Start and wait till the VM starts
  • login to the machine using the following user credentials 
    usrname  : learn
password : <classpassword>
  • Check the IP address by using the command ifconfig. The result should be as following. 
    enp0s3    Link encap:Ethernet  HWaddr 08:00:27:e6:60:87
          inet addr:10.0.20.1  Bcast:10.0.20.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fee6:6087/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:286 errors:0 dropped:0 overruns:0 frame:0
          TX packets:830 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:35607 (35.6 KB)  TX bytes:61166 (61.1 KB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:686 errors:0 dropped:0 overruns:0 frame:0
          TX packets:686 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1
          RX bytes:58320 (58.3 KB)  TX bytes:58320 (58.3 KB)

Running Dynagen/Dynamips

Dynamips is a Cisco router emulator. It emulates 2691, 3620, 3640, 3660, 3725, 3745, and 7206 hardware platforms, and runs standard IOS images.

Dynagen is a text-based front end for Dynamips, which uses the “Hypervisor” mode for communication with Dynamips. Dynagen simplifies building and working with virtual networks

  • First login to campuslan VM.
  • Then start up the Dynamips server on your local machine 
    dynamips –H 7100 &

hypervisor will run on port 7100

  • You can find the topology file in /var/dynamips/campuslan.net
  • Run the topology file with dynagen 
    dynagen /var/dynamips/campuslan.net
  • Now you have the network topology running. Give the following command in dynagen 
    => list
  • Your result should be something like this 
    Name       Type       State      Server          Console
AccessRt   3725       stopped    localhost:7100  2100
CampusCore 3725       stopped    localhost:7100  2200
FacACore   3725       stopped    localhost:7100  2300
FacBCore   3725       stopped    localhost:7100  2400
FacASw     3725       stopped    localhost:7100  2500
FacBSw     3725       stopped    localhost:7100  2600
  • You can see there are 6 devices. But none of them are running. You can also see the numbers of the ports which the console port of devices are running. This will also be helpful to you in next steps
  • you can get details about devices by following command 
    => show device <device name>
  • This Command will be helpful to know on which interface the devices are connected to each other 
    => show device AccessRt
Router AccessRt is stopped
  Hardware is dynamips emulated Cisco 3725 with 256 MB RAM
  Router's hypervisor runs on localhost:7100, console is on port 2100
  Image is shared c3725-adventerprisek9-mz124-15.bin-localhost.ghost with idle-pc value of 0x60a8033c
  Idle-max value is 100, idlesleep is 30 ms
  55 KB NVRAM, 128 MB disk0 size, 0 MB disk1 size
   slot 0 hardware is GT96100-FE with 2 interfaces
      FastEthernet0/0 is connected to router CampusCore FastEthernet1/15
      FastEthernet0/1 is connected to real enp0s3 interface
  • Now you can start the devices. To start the devices use the start command 
    => start AccessRt
=> start CampusCore
=> start FacACore
=> start FacBCore
=> start FacASw
=> start FacBSw
  • It will take some time to boot up all the devices. After that you will have the following topology up and running and you can start configuring the routers and switches.

Network Topology

https://ws.learn.ac.lk/raw-attachment/wiki/ipv6vmconf/InitialTopology.jpg

Attachments (2)

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.