= IPv6 in a Campus Network Hands - On = In this Hands-on you will be given a virtual campus LAN. You will configure devices (Cisco based) in both IPv4 and IPv6. After the configurations, you will get a virtual campus network with IPv4/IPv6 dual stack. Each institute you represent will be given a campus LAN. Those who represent the same institutes have to work together as a group, everybody in the group will get a single campus network (remember to sit together in a same row) Your virtual campus network will then be connected to the virtual PCs (VMs) exactly as real PCs and also to to real Internet that let you to see how real data passes through your virtual campus network. You will be browsing Internet, checking email, etc through this virtual campus network. This emulation of the campus network has been done by the use of Dynagen/Dynamips. The whole setup reside in three VMs. 1. VM for the Campus LAN (Dynage/Dynamips installed) 2. Two VMs for the Department PCs All three VMs (Ubuntu 64) has already been created as Virtul Hard Disk (in VDI format) and available for you to quickly download. It can be easily launch using Oracle Virtual Box. You will get the topology file in the CampusLAN VM. The other two VMs will used as PCs, or servers located in user end of your campus LAN. == Setting up the Virtualbox == === Installation of virtualbox and Downloading virtual hard disks === - Download and install virtualbox 5.0.x​ - Download the Virtual Hard disks from the LEARN mirror. You can get them by following links * [http://192.248.4.40/ipv6/campuslan.vdi campuslan.vdi] * [http://192.248.4.40/ipv6/FacAPC.vdi FacAPC.vdi] * [http://192.248.4.40/ipv6/FacBPC.vdi FacBPC.vdi] - Note down the location of downloaded vdi files === Creating the VM CampusLAN === - Start VirtualBox and Click on '''New''' button (at top-right) to create new virtual machine - Enter name of the VM as '''CampusLAN''' - Select OS Type: '''Linux''' - Select Version: '''Ubuntu (64-bit)''' - Then click on Continue button - Set VM's memory size to '''1536MB''' and click on Continue button - Set VM's hard disk option to '''Use an existing virtual hard disk file''' and click the browse button and browse to the location where you download the virtual hard disks. Then select the '''campuslan.vdi''' file and click on the create button. - You will see a new virtual machine named CampusLAN appears on Virtual Box Manager Window ==== Setting up Network Interfaces ==== - Select the CampusLAN VM from left panel on Virtual box, right click and open '''Settings''' - Click on the '''Network''' title - On '''Adapter 1''' check the '''Enable Network Adapter''' . Then change '''Attached to be''' to the '''Bridged Adapter''' and make sure the '''name''' of the interface is the same interface which you use to connect to the outside (Either Wi-Fi or Ethernet). This virtual interface will work as the WAN port of the of your virtual campus network that can be used to connect from out side. - Click on '''Advanced''' drop down list and change the '''promiscuous mode''' to '''Allow All''' - On '''Adapter 2''' check the '''Enable Network Adapter''' . Then change '''Attached to be''' to the '''Internal Network''' and give the Name of the network as '''VLAN10'''. This virtual interface will connect to a internal virtual bridged network. - Click on '''Advanced''' drop down list and change the '''promiscuous mode''' to '''Allow All''' - On '''Adapter 3''' check the '''Enable Network Adapter''' . Then change '''Attached to be to''' the '''Internal Network''' and give the Name of the network as '''VLAN20'''. This virtual interface will connect to a internal virtual bridged network. - Click on '''Advanced''' drop down list and change the promiscuous mode to '''Allow All''' - Click '''OK''' === Creating the VM FacAPC === - Start virtualbox and Click on '''New''' button (at top-right) to create new virtual machine - Enter name of the VM as '''FacAPC''' - Select OS Type: '''Linux''' - Select Version: '''Ubuntu (64-bit)''' - Then click on Continue button - Set VM's memory size to '''512MB''' and click on Continue button - Set VM's hard disk option to '''Use an existing virtual hard disk file''' and click the browse button and '''browse''' to the location where you download the virtual hard disks. Then select the '''FacAPC.vdi''' file and click on the create button. - You will see a new virtual machine named FacAPC appears on Virtual Box Manager Window ==== Setting up Network Interface ==== - Select the FacAPC VM from left panel on Virtual box, right click and open '''Settings''' - Click on the '''Network''' title - On '''Adapter 1''' check the '''Enable Network Adapter''' . Then change '''Attached to be''' to the '''Internal Network''' and give the Name of the network as '''VLAN10'''. This virtual interface will connect to a internal virtual bridged network. - Click on '''Advaned''' drop down list and change the '''promiscuous mode''' to '''Allow All''' - Click '''OK''' === Creating the VM FacBPC === - Start virtualbox and Click on '''New''' button (at top-right) to create new virtual machine - Enter name of the VM as '''FacBPC''' - Select OS Type: '''Linux''' - Select Version: '''Ubuntu (64-bit)''' - Then click on Continue button - Set VM's memory size to '''512MB''' and click on Continue button - Set VM's hard disk option to '''Use an existing virtual hard disk file''' and click the browse button and '''browse''' to the location where you download the virtual hard disks. Then select the '''FacBPC.vdi''' file and click on the create button. - You will see a new virtual machine named FacBPC appears on Virtual Box Manager Window ==== Setting up Network Interface ==== - Select the FacAPC VM from left panel on Virtual box, right click and open '''Settings''' - Click on the '''Network''' title - On '''Adapter 1''' check the '''Enable Network Adapter''' . Then change '''Attached to be''' to the '''Internal Network''' and give the Name of the network as '''VLAN20'''. This virtual interface will connect to a internal virtual bridged network. - Click on '''Advaned''' drop down list and change the '''promiscuous mode''' to '''Allow All''' - Click '''OK''' After Creating all three VM's. Your VM setup will look like this. [[Image(https://ws.learn.ac.lk/raw-attachment/wiki/ipv6vmconf/VMSetup.jpg)]] === Setting UP IP Addresses === ==== CampusLAN VM ==== Before running Dynagen you have to start your VMs and assign IP address to the VM's network interfaces. - Select the '''CampusLAN''' VM from left panel on Virtual box, right click '''Start''' and wait till the VM starts - login to the machine using the following user credentials {{{ usrname : learn password : }}} - Then change the '''interfaces''' file. Root password is the same as class password {{{ sudo vi /etc/network/interfaces }}} - locate the following lines {{{ iface enp0s3 inet static address 192.168.56.2 netmask 255.255.255.0 network 192.168.56.0 broadcast 192.168.56.255 gateway 192.168.56.1 dns-nameservers 192.248.1.161 }}} - Change it to the following lines. You can find your IP Address from this table {{{ iface enp0s3 inet static address netmask 255.255.255.0 network 192.248.4.0 broadcast 192.248.4.255 gateway 192.248.4.254 dns-nameservers 192.248.1.161 }}} - Save and Exit the editor (type ''':wq''') - When you completed the IP settings , restart the Interfaces {{{ sudo /etc/init.d/networking restart }}} - Confirm the correct IP settings by '''ipconfig''' command. Your result should be something like the following. Check the IP address of enp0s3 Interface and see whether the other interfaces are up {{{ enp0s3 Link encap:Ethernet HWaddr 08:00:27:8c:e0:26 inet addr: Bcast:192.248.4.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe8c:e026/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1120 errors:0 dropped:0 overruns:0 frame:0 TX packets:7550 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:99387 (99.3 KB) TX bytes:567441 (567.4 KB) enp0s8 Link encap:Ethernet HWaddr 08:00:27:f0:f7:66 inet6 addr: fe80::a00:27ff:fef0:f766/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:648 (648.0 B) enp0s9 Link encap:Ethernet HWaddr 08:00:27:51:68:d3 inet6 addr: fe80::a00:27ff:fe51:68d3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:648 (648.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:11840 (11.8 KB) TX bytes:11840 (11.8 KB) }}} - Try ping to some known hosts and see the results. {{{ ping 192.248.4.254 ping 192.248.1.161 ping www.google.com }}} ==== FacAPC VM ==== As this is a PC inside your virtual LAN it has a private IP address. The address is already configured. You can verify whether it is correct. - Select the '''FacAPC''' VM from left panel on Virtual box, right click '''Start''' and wait till the VM starts - login to the machine using the following user credentials {{{ usrname : learn password : }}} - Check the IP address by using the command '''ifconfig'''. The result should be as following. {{{ enp0s3 Link encap:Ethernet HWaddr 08:00:27:e9:76:20 inet addr:10.0.10.1 Bcast:10.0.10.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fee9:7620/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:198 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23291 (23.2 KB) TX bytes:15516 (15.5 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:11840 (11.8 KB) TX bytes:11840 (11.8 KB) }}} ==== FacBPC VM ==== As this is a PC inside your virtual LAN it has a private IP address. The address is already configured. You can verify whether it is correct. - Select the '''FacBPC''' VM from left panel on Virtual box, right click '''Start''' and wait till the VM starts - login to the machine using the following user credentials {{{ usrname : learn password : }}} - Check the IP address by using the command '''ifconfig'''. The result should be as following. {{{ enp0s3 Link encap:Ethernet HWaddr 08:00:27:e6:60:87 inet addr:10.0.20.1 Bcast:10.0.20.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fee6:6087/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:286 errors:0 dropped:0 overruns:0 frame:0 TX packets:830 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:35607 (35.6 KB) TX bytes:61166 (61.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:686 errors:0 dropped:0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:58320 (58.3 KB) TX bytes:58320 (58.3 KB) }}} === Running Dynagen/Dynamips === '''Dynamips''' is a Cisco router emulator. It emulates 2691, 3620, 3640, 3660, 3725, 3745, and 7206 hardware platforms, and runs standard IOS images. '''Dynagen''' is a text-based front end for Dynamips, which uses the “Hypervisor” mode for communication with Dynamips. Dynagen simplifies building and working with virtual networks - First login to CampusLAN VM. - Then start up the Dynamips server on your local machine {{{ dynamips –H 7100 & }}} hypervisor will run on port 7100 - You can find the topology file in '''/var/dynamips/campuslan.net''' - Run the topology file with dynagen {{{ dynagen /var/dynamips/campuslan.net }}} - Now you have the network topology running. Give the following command in dynagen {{{ => list }}} - Your result should be something like this {{{ Name Type State Server Console AccessRt 3725 stopped localhost:7100 2100 CampusCore 3725 stopped localhost:7100 2200 FacACore 3725 stopped localhost:7100 2300 FacBCore 3725 stopped localhost:7100 2400 FacASw 3725 stopped localhost:7100 2500 FacBSw 3725 stopped localhost:7100 2600 }}} - You can see there are 6 devices. But none of them are running. You can also see the numbers of the ports which the console port of devices are running. This will also be helpful to you in next steps - you can get details about devices by following command {{{ => show device }}} - This Command will be helpful to know on which interface the devices are connected to each other {{{ => show device AccessRt Router AccessRt is stopped Hardware is dynamips emulated Cisco 3725 with 256 MB RAM Router's hypervisor runs on localhost:7100, console is on port 2100 Image is shared c3725-adventerprisek9-mz124-15.bin-localhost.ghost with idle-pc value of 0x60a8033c Idle-max value is 100, idlesleep is 30 ms 55 KB NVRAM, 128 MB disk0 size, 0 MB disk1 size slot 0 hardware is GT96100-FE with 2 interfaces FastEthernet0/0 is connected to router CampusCore FastEthernet1/15 FastEthernet0/1 is connected to real enp0s3 interface }}} - Now you can start the devices. To start the devices use the start command {{{ => start AccessRt => start CampusCore => start FacACore => start FacBCore => start FacASw => start FacBSw }}} - It will take some time to boot up all the devices. After that you will have the following topology up and running and you can start configuring the routers and switches. === Network Topology === [[Image(https://ws.learn.ac.lk/raw-attachment/wiki/ipv6vmconf/InitialTopology.jpg)]]